ULN2804

$33.00

WiFi BEE

$299.00

POLEA POLEAS JUEGO

$55.00
BOLSA CON 6 POLEAS EN DIFERENTES TAMAÑOS ( Diámetro: 6 mm, 13 mm, 15 mm, 16,8 mm, 18 mm, 24 mm)

PRODUCTO AGOTADO!!!! SINTRA PLASTICO TERMOMOLDEABLE

$66.00
TODAVIA SIGUES CONSTRUYENDO TUS ROBOTS CON MADERA, TRIPLAY, ACRILICO, CARTONCILLO O MATERIALES PESADOS E INADECUADOS??? EL SINTRA ES UN MATERIAL EXCELENTE PARA CONSTRUIR CHASIS DE ROBOTS,PROYECTOS, ESTRUCTURAS, ETC...LIGERO RESISTENTE,DURABLE, FACIL DE MANEJAR ADEMAS ES UN MATERIAL termodeformable, es decir, se puede doblar al sumergirlo en agua caliente y mantener esa forma al enfriarse.UNA VEZ MOLDEADO, LO PUEDES PINTAR, TALADRAR, REBAJAR, ETC... Medidas: 20x30 cm. Grosor: 3mm.

RUEDA LLANTA GRUESA

$35.00
RUEDA GRUESA PARA ROBOTS, COCHES Y PROYECTOS EN GENERAL. ACABADO REALISTA. HULE ANTIDERRAPES, RELLENA DE "AIRE" , DEFINITIVAMENTE UNA EXCELENTE RUEDA PARA TRABAJOS DE MAYOR CALIDAD.

RUEDA LOCA JAPONESA METALICA

$52.00
This ball caster kit includes a black ABS housing, a 1/2" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets. The total height of the ball caster, 0.53", can be increased to about 0.7" using the included spacers. The two included #2 screws can be used to mount the ball caster to your chassis (the distance between the screw holes is 0.58"). Note that our ball casters are designed for small robots; they are not intended to bear more than a few pounds. With more weight than this, friction between the ball and the housing will probably keep it from rolling well.

RUEDA LOCA METALICA

$40.00
RUEDA LOCA METALICA, SOPORTA HASTA 9KG!!, PESO: APROX:60GR.,MEDIDAS: ALTURA 22mm, ANCHO BOLA 18mm, DE ORIFICIO A ORIFICIO 13.5mm. SE RECOMIENDA LUBRICAR DE VEZ EN CUANDO.

RUEDA LOCA PLASTICA JAPONESA

$55.00
ESTA RUEDA LOCA ES DE MEJOR CALIDAD EN MATERIALES Y RESISTENCIA DE LAS RUEDAS LOCAS "ECONOMICAS" (ROLL ON), SOPORTA CASI 3Kg DE PESO Y EL MATERIAL TIENE FACIL "DESLIZAMIENTO" PARA QUE TU ROBOT SEGUIDOR DE LINEAS NO SE ATORE. INCLUYE ACCESORIOS

RUEDA LOCA TIPO SILLA

$35.00
RUEDA LOCA SILLA DE "OFICINA" VERSIÓN ECONÓMICA Y RESISTENTE. SOPORTA HASTA 20Kg!!! MATERIA PLÁSTICO Y METÁLICO. MEDIDAS: 35mm de diámetro, x 14mm de ancho. Con altura total de piso a base de 43mm.

SUMO BLADE ZUMO PALA #1410

$115.00
OJO!!! EL PRODUCTO ES SOLO LA "PALA" This basic sumo blade (sometimes also called a “scoop”) is intended for use with the Zumo chassis and included as part of the assembled Zumo Robot for Arduino. (Note: It is not the same as the blade included with the newer Zumo 32U4 Robot, and it is not intended for use with this version of the Zumo robot.) It is made of 0.036″-thick, laser-cut stainless steel, and it ships flat as shown in the product picture. The two tabs must be bent to an angle of approximately 70° before it can be mounted to the front of the Zumo chassis. We recommend using a pair of long-nose pliers to bend the tabs.

TM4C123GXL TIVA.

$999.00
PRODUCTO ESCASEANDO. SUBIDA DE PRECIOS..... TARJETA DE DESARROLLO Núcleo: ARM Cortex M4F Marca: Texas Instruments Ancho de bus de datos: 32 bit Descripción/Función: Evaluation Board for the evaluation of ARM Cortex M4F microcontrollers. Dimensiones: 50 mm x 57.15 mm x 107.95 mm Para utilizar con: TM4C123G Tipo de interfaz: USB Voltaje de alimentación operativo: 5 V Peso de la unidad: 116 g

ULN2804

$33.00
ARREGLO DE TRANSISTORES, ENCAPSULADO DIP-18

WiFi BEE

$299.00
Wifi Bee-ESP8266 is a Serial-to-WIFI module using XBEE design in a compact size, compatible with XBEE slot, applicable to a variety of 3.3V single-chip system. It can be used for Arduino, wireless data transfer, remote control. On-board switch can be used to easily select the Startup module or Upgrade firmware. ESP8266 has a powerful on-chip processing and storage capacity, built-in 32-bit processor, built-in Lwip protocol stack. Support AP+STA mode co-exist. And you could configure various parameters via AT commands. Note: Since the STA mode which support the Server mode is not stable, we are working on that you could refer to the ESP8266 manual book to try. Note: In order to configure this module, you will need an adapter or Xbee shield that lets you communicate with the module, before you can plug it and use on other modules.