ACS714 SENSOR DE CORRIENTE DC

$150.00
This board is a simple carrier for Allegro’s ±5A ACS714 Hall effect-based linear current sensor. This version accepts a bidirectional current input with a magnitude up to 5 A. The output is an analog voltage (185 mV/A) centered at 2.5 V with a typical error of less than 1.5%.

CORRIENTE SENSOR DE 10A TA17-03

DESCONTINUADO!!!! DESCONTINUADO!!!! SENSOR DE CORRIENTE 10A, NO INVASIVO. Is Electronic building block, a transformer, an ammeter, a current sensor module, compatible with all kinds of Arduino electronic building blocks / sensor shield 3P electronic building blocks interface, input 5V - GND, S pin for output an analog voltage value. For details, see product manual. You can conveniently connect to the Arduino board via the Freaduino sensor shield or Freaduino UNO and similar sensors / electronic building block shield.

INA219 SENSOR DE CORRIENTE I2C

$150.00
Sensor de corriente INA219 Voltaje de funcionamiento: 3-5v y soporta lecturas de hasta 26v ¿Cómo funciona? Un amplificador mide el voltaje a través de una resistencia de 0.1ohm y 1% de tolerancia. Ya que la entrada máxima del amplificador es de ±320mV significa que puede medir hasta ±3.2 Amps. Y con el ADC de 12 bits el rango de resolución es de 0.8mA y el rango de lectura de corriente es ±3.2A

MOTOR CORRIENTE DIRECTA 6V ESTUDIANTES

$25.00
MOTOR SENCILLO PARA EXPERIMENTOS ,PROYECTOS,ETC...3V a 6V, MÁXIMO 9V speed: 20000 r / min, 6V speed: 40000 r / min, Main dimensions: 25 x 15 x 20mm, Motor shaft length: 9mm, shaft diameter 2mm, Rated voltage: 3V, Reference current: 0.35-0.4A.

SENSOR DE CORRIENTE ALTERNA 100A TC

$250.00
Sensor de corriente alterna hasta 100A, compatible con Arduino, Cypress, PIC, etc..., Frec. de trabajo 20Hz a 20Khz,salida estandarizada y lineal.Ideal para proyectos de energía y ahorro. Salida con pin tipo estero de 3.5mm. TAMBIEN MANEJAMOS DE 30A

VOLTIMETRO Y AMPERIMETRO DC, NUEVO MODELO!!!

$140.00
VOLTIMETRO Y AMPERIMETRO PARA CORRIENTE DIRECTA, DSN-VC288 MAXIMO 100Volts, MAXIMO 10Amperes, CONEXION FACIL, IDEAL PARA FUENTES DE ALIMENTACION. 46 X 27 mm. Thin Red Wire (VCC): positive pole of power supply input (3.5-30V) (Note: if the measuring signal is less than 30V and the power is adequate, can be the power supply of module) Thin Black Wire (GND): negative pole of power supply input (3.5-30V, common ground with measuring signal) Green Wire (VIN): positive pole of measuring signal input (0-100V) Thick Red Wire (I+): positive pole of current input (series connect on the power supply cathode) Thick Black Wire (I-): negative pole of current input (series connect on the power supply cathode

WATTIMETRO 100A 80-260Vac

$390.00
"WATTIMETRO", MEDIDOR DE POTENCIA ELÉCTRICA, SIMILAR A LOS DE LAS COMPAÑÍAS PROVEEDORAS DE LUZ. 80 a 260Vac Y HASTA 100A,HASTA 22KW. MEDIDAS: 79mm x 43mm x 48mm. EL DIAGRAMA DE CONEXIÓN ESTA EN LA PARTE DE ATRÁS, LA CONEXIÓN INCORRECTA DAÑA EL EQUIPO, MUCHO CUIDADO!!!